They are making a few good observations regarding How to Install a Bathtub: Install an Acrylic Tub and Tub Surround in general in this post followed below.
Setting up a bath tub isn't exactly rocket science, however it does call for strong plumbing, carpentry, and often, tiling abilities. Changing an old bath tub with a new one is likewise a reasonably hard project. If the old tub is readily available, the job can move immediately; if you need to open a wall to get rid of the old bathtub and also place the brand-new tub, the task is much harder. In either case, the task is within a home handyman's skills, although you will certainly require a helper to move out the old bathtub and also embeded in the new one. Make sure you have actually certified on your own for the task and fit attempting it. Rather than working with a service provider to take over a halfway-completed project, it is far better to think about utilizing one prior to you begin. Opportunities are you may require an expert plumber to make tube links.
This article will assist you mount a new tub in your restroom if you have actually already acquired a brand-new bathtub and do not need to alter the arrangement of your previous water pipes.
Your devices and product list ought to consist of the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installment, then the first thing you should do is disconnect the supply of water. After doing so, turn on the taps to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be quite bothersome as a result of the limited gain access to that is commonly the instance.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will come from the pipelines. Once the supply pipes have actually been gotten rid of, use the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from turning during this process. When the faucets have been gotten rid of, the holes in the bath/basin will need to be cleansed of any kind of old sealing compound.
Prior to going on to fit the new taps, contrast the pipe links on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will require a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the tap and also the other end provides a link to the existing supply pipelines.
If you require to fit a monobloc, then you will certainly need reducing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, place the faucet in the installing opening in the bath/basin making sure that the washers are in location in between the tap and the sink. Safeguard the tap in place with the maker offered backnut. Once the tap is securely in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with regular tap adapters. The previous kind needs to be linked to the tap ends initially, tightening only by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been connected.
Setting up the Bathtub
Using both wooden boards under its feet, place the bath tub in the needed position. The wooden boards are valuable in evenly spreading out the weight of the bathtub over the location of the boards rather than concentrating all the weight onto four tiny points.
The following goal is to make sure that the tub is leveled all round. This can be accomplished by examining the level and also changing the feet on the bath tub until the level reads level.
To install taps, fit the bottom of the furthest flexible faucet adapter to the proper supply pipe by making a compression join; after that do the very same for the various other faucet.
Turn on the water system and also inspect all joints and brand-new pipework for leakages as well as tighten them if necessary. Load the bath tub and likewise examine the overflow outlet and the typical electrical outlet for leakages.
Ultimately, deal with the bath paneling as described in the manufacturer's user's manual. Tiling as well as securing around the tub needs to wait until the bath tub has been used at least when as this will certainly settle it into its last setting.
Preparing for the Installation
To start with, the supporting structure supplied with the bathroom should be fitted (if needed) according to the supplier's directions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is important to ensure that if the faucet comes with a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the taps device to prevent strain on the bathtub.
Fit the flexible faucet adapters to the bottom of both taps using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet via the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Make certain you utilize every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom must currently be ready to be fitted in its last position.
Tiling Around the Tub
In the location where the bathroom meets the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to split an inflexible seal, creating the water to pass through the wall surface in between the bath and the tiling, resulting in problems with dampness and feasible leakages to the ceiling below.
You can choose from a variety of coloured sealers to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and can sealing gaps as much as a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always fill up the tub with water before sealing, to allow for the activity experienced when the bathtub is in usage. The sealer can break rather very early if you do not take into consideration this movement prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise conveniently offered on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water-proof glue and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you enjoyed our post about Tools You Need to Install a New Bathtub . Thanks so much for finding the time to read our post. Be sure to set aside a second to promote this write-up if you liked it. Kudos for your time. Come back soon.
Leak? Reach out!